FAQs

Q?Why are my shingles curling?
A.

faqshinglecurl

Asphalt, an oil based product, is resistant to water and used in a wide range of waterproofing areas. The majority of shingles used today are primarily asphalt in construction, and asphalt does dry-out over time, this process is called oil migration. As with most natural elements when asphalt dries it shrinks that’s why shingles have a fiberglass intermat that tries to prevent the shrinkage. Over time though the intermat will begin to fail as the asphalt expands and shrinks, and that is when you start to see curling; other factors like improper ventilation accelerates the curling process by giving the asphalt more periods of frequent movement. When curling occurs, accelerated damage can occur to your roof, it may be time for a new roof.

Q?What is granular loss?
A.

faqgranularloss

 

Shingles use small colored stone chips called granules to protect the asphalt from environmental elements (such as UV light) and to provide an aesthetically pleasing look. Over time these granules wear off and when this occurs the asphalt surface starts to break down causing a downward turn in the shingle’s life. This is the reason why it is not recommended to pressure clean a shingle roof. We have found improper ventilation to be a major cause of premature granule loss; and as an added precaution it is also important to keep overhanging trees trimmed so they LAO don’t brush off granules. If you notice shingles going bare that means that a roof replacement is near.

 

Q?What are the results from standing water on my roof?
A.

faqpondingwater

Ponding water is a code violation and warranty exclusion on all asphalt based roof systems, this is categorized when water sits on a roof for more than 48 hours without evaporating or running off naturally. Water ponding breaks down asphalt, which is an oil-based product. The issue with ponding water is that oil is trapped at the bottom and due to it’s natural properties, it tries to rise to the top causing oil migration. When the oil is then pulled out from the material it then starts to lose its waterproofing ability then in turn causes the system to break down.

Q?Why do I get torn, cracked or broken surfaces on my roof?
A.

faqcracking

As a roof expands and contracts the components that hold it together begin to push and pull against one another. This is a daily occurrence and is associated with thermal shock, and after years of this type of movement something usually gives. Other factors can be purely kinetic such as a tree branch or flying debris may impact the roof; or third party damage such as foot traffic can cause damage. When the membrane is damaged this can lead to leaks so its recommended that these areas be patched/repaired as soon as possible.

Q?Do I get a warranty when i get a new roof?
A.

We stand behind our work proudly, and to give you peace of mind we offer a standard 5 year workmanship warranty on the roofs we install, this goes hand-in-hand with the manufacturer’s warranty.

Q?Do I need to install gutter guards on my roof?
A.

faqguttergards

They are more than worth the investment if you have trees or other foliage that are tall enough to blow onto the roof. They virtually eliminate clogged downspouts and leaf build up in the gutters.

Q?How can I stop ice dams from forming on my roof?
A.

The best prevention of ice dams is a well-ventilated roof, also known as a cold roof. Make sure your attic area has sufficient air exhaust outlets (gable vents, ridge vents and free air vents) and that the airflow is distributed throughout the attic space. Peak mounted ridge vents such as Shingle Vent II maximize airflow in attic areas.
Homes and buildings with cathedral or open ceilings may want to consider installing ceiling fans near the peak of the ceiling to help push the warmer air away from these areas.

Q?How do I stop moss growth on my roof?
A.

Moss growth is a abundant issue in the midwest, usually noted by black streaks on shingles, they become more noticeable as your roof ages. There are many ways to deal with moss, the easiest being a water+bleach mix wash if your roof is already showing signs of growth (DO NOT PRESSURE WASH). The preventative measure being to install zinc or copper strips on the ridge of the roof to inhibit moss growth.

Q?How can I deal with Mold growth?
A.

The best way to deal with mold is to prevent the mold from growing, this is usually through a well ventilated and dry attic, keeping a low humidity level in your insulated space. Mold, unlike moss, does not need sunlight to thrive, and appears as black spots inside your attic and as black streaks on your shingles. Once mold has taken root, a licensed mold remediator is your best bet for mold removal; if mold growth has been left unchecked it can rot away the plywood and repair expenses could skyrocket. So its always best to do preventive maintenance or call a professional as soon a you see early signs of mold.